相关文档

• 单片机整板测试程序.doc

  开发板测试程序：要求：串口提示测试项目根据输入单片机进行相应的测试具体流程如下：首先单片机一上电串口输出如下所示选项假如选择测试DS1302 电脑键盘上输入数字8再按下回车进入下面界面开始1302的测试只要键盘上按下ESC键即可终止测试回到选择界面锻炼技巧：串口通信各种常用单片机外设的驱动技术 :

• L3G4200D51单片机IIC测试程序.doc

  这是L3G4200D 51单片机IIC 测试程序这是1602 头文件 保存为 1602.hdefine DataPort P0 LCD1602数据端口sbit LCD_RS=P24 LCD1602命令端口sbit LCD_RW=P25 LCD1602命令端口sbit LCD_EN=P26 LCD1602命令端口 include <IN

• 单片机串口测试程序.doc

  程序作用:测试单片机串口功能将串口接收到的字符重新发送到串口上程序在STC12C2052AD上实验成功晶振为使用串口调试软件测试单片机收到回车键即显示你发送的字符 单片机交流:QQ949725852 include<> define uint unsigned intdefine uchar unsigned chardefine word_num 32 能接收的字符字数当然不能

• AT89C51单片机开发板程序.doc

  AT89C51单片机开发板程序1个LED数码管静态显示(0-9)include<>define uchar unsigned chardefine uint unsigned intuchar iuchar code a[]={0xc00xf90xa40xb00x990x920x820xf80x800x90}void delay(uint

• 51单片机测温程序.docx

  include<reg52.h>include<intrins.h>define uint unsigned intdefine uchar unsigned charuint inumonenumtwotempuchar qianbaishigexiaoshusbit dq=P22sbit dula=P26sbit wela=P27ucharcode list[]={0x3f 0x06

• 单片机程序.doc

  单片机程序include <>include <>extern float sqrt(float x)extern float exp(float x)extern float tan(float x)extern float cos(float x)extern float sin(float x)extern float log10(float x)void reset()void di

• 单片机程序.doc

  行线接－列线接－根据扫描键盘返回的键值编码查键值编码表从而得到键值并送数码管显示开机时数码管显示－当键按下时数码管显示按下键的键值蜂鸣器响一声 include <>include <>define uchar unsigned chardefine uint unsigned intsbit BEEP = P36 蜂鸣器驱动线uchar keyunsig

• 单片机程序.doc

  1. 延时跑马灯 ORG 0 AJMP MAINMAIN: MOV SP5FH MOV DPTRTAB LOOP0: MOV A0 MOV R28LOOP: MOV BA MOVC AADPTR MOV P0A LCALL DEL MOV AB INC A

• 单片机程序.doc

  5include <>void delay(void){unsigned int aa=55400while(a--)}void main(){while(1){P0=0xfe11111110delay()P0=0xffdelay()}}61include <>sbit led0=P00sbit led1=P01sbit led2=P02sbit led3=P03sbit led4=P04sbit

• 单片机程序.doc

  #