相关文档

• 简约ATMEGA8流水灯练习c程序仿真.doc

  include<>void delay_1ms(void){unsigned int ifor(i=1i<(unsigned int )(1144-2)i)}void delay_ms(unsigned int n){unsigned int i=0while(i<n){ delay_1ms() i}}void main(){unsigned char iDDRD=0xFFPORT

• 51单片机流水灯C程序.doc

  P0口控制先奇数亮再偶数亮循环三次一个灯上下循环三次两个分别从两边往中间流动三次再从中间往两边流动三次不过这个程序实现的 应该是这样的? 先奇数亮再偶数亮循环三次一个灯上下循环三次两个分别从两边往中间流动再从中间往两边流动(延时0.1s)include< reg52.h>include< intrins.h>define uint unsigned intdefine uchar unsig

• 流水灯程序.doc

  include<>include<>define uchar unsigned chardefine uint unsigned intsbit dula=P26 sbit wela=P27uchar numnum1num2baishigeuchar code table[]={0x3f0x060x5b0x4f0x660x6d0x7d0x070x7f0x6f0x770x7c0x390x5e0x7

• 流水灯程序.doc

  #

• 单片机32个IO口流水灯C程序.doc

  单片机32个IO口流水灯C程序(转)2008-11-23 11:3789C51S51单片机32个IO口流水灯测试程序Flash0123分别对应单片机的P0123四个口a程序对应流水灯从全灭到一个一个亮b程序对应流水灯从全亮到一个一个灭Author:大灵通2006-7-26 10:57OKinclude<>include<>include<>define uchar unsigned char

• 广告流水灯程序.doc

  广告流水灯程序ORG 00HMOV P280HSTART:MOV A0FFH 赋初值 CLR C MOV R28LOOP:RRC A 带进位右移 MOV P1A CALL DELAY DJNZ R2LOOP MOV R27LOOP1:RLC A 带进位左移 MOV P1A

• 流水灯[汇编程序].doc

  4.1 流水灯程序介绍：利用P1 口通过一定延时轮流产生低电平输出以达到发光二极管轮流亮的效果实际应用中例如：广告灯箱彩灯霓虹灯闪烁程序实例(LAMP.ASM)ORG 0000HAJMP MAINORG 0030HMAIN:9MOV A00HMOV P1A 灭所有的灯MOV A11111110BMAIN1:MOV P1A 开最左边的灯ACALL DELAY 延时RL A 将开的灯向右边移AJ

• 心形流水灯程序.doc

  include<>include <>define uint unsigned intdefine uchar unsigned char 延时void delay(uint k) {uint ijfor(i=ki--i>0)for(j=100j--j>0)}void main(){uchar temp0temp1uchar yiuchar yi0yi1

• 心形流水灯程序.doc

  include<>include <>define uint unsigned intdefine uchar unsigned char 延时void delay(uint k) {uint ijfor(i=ki--i>0)for(j=100j--j>0)}void main(){uchar temp0temp1uchar yiuchar yi0yi1

• Libero9.0简易仿真流程.doc

  一 写源代码1 点击上图的红色部分的 HDL Editor 弹出如下对话框2 如上图选择所用语言类型并输入文件名点击OK后进入代码设计二 写激励文件1 点击 HDL Editor弹出如下对话框： 如上图激励文件应选择左边的 HDL Stimulus File 类型并对该文件命名2 激励文件写好后点击 Files 即可看到如下界面三 Modsim 仿真1 点击 Projec选择 Setting